恒泰源聚氨酯

我们专注于鞋底用聚氨酯

>
>
>
中高密度中硬度聚氨酯鞋底原液ZG-P-8130/ZG-I-8260

中高密度中硬度聚氨酯鞋底原液ZG-P-8130/ZG-I-8260

产品编号
所属分类
耐寒鞋底料
数量
-
+
库存:
Product description
参数

中硬度中高密度聚氨酯耐寒鞋鞋底原液

牌号(Shop sign): ZG-P-8130/ZG-I-8260

耐寒鞋鞋底原液

PU Resin for shoe sole of cold-resistant shoes

1. 特性:中硬度,中高密度。耐寒,半耐寒。

Characteristic: Medium hardness, medium and low density, cold resistance and semi cold resistance

2. 用途:适用于耐寒,半耐寒男女鞋底的生产。

Application: Applicable to the production of cold-resistant and half hardy soles for both men and women shoes

3. 原液特性Typical properties of PU Resin

3. 原液特性Typical properties of PU Resin

品  名

Name of products

外   观

Appearance

粘   度Viscosity(Pa·s/50℃) 密   度Density(g/cm3/40℃) 包  装Package(kg)
ZG-P-8130 白色或淡黄,液状无异物White or pale yellow, liquid, no foreign material 1.00-1.40 1.16-1.20 18
ZG-I-8260 透明液体无异物Transparent liquid, no foreign materials 0.20-0.40 1.18-1.20 20

参考发货配比(Reference shipments ratio):A/B=30/24(桶)

Reference shipments ratio: A/B=30/24(barrel)

4. 成型条件及物性值(Molding conditions & physical properties): 

测试项目Test item 参考物性值Reference physical properties
鞋底成型密度Molded density of sole(g/cm3 0.25~0.65
硬度(A型)Hardness (type A) 35~65
拉伸强度Tensile strength(MPa) 3.5~4.5
伸长率Elongation(%) 250~550
NBS耐磨NBS abrasion resistance (%) ≥10%
自由泡密度Free foam density(g/cm3 0.15~0.35
耐折性(常温)(4万次裂口长度,mm)Folding endurance (room temperature)(40,000 gap length mm) <8

●配合比率是以最佳配比值为基础,此配比值会随添加的颜料助剂种类和添加量不同而变化。

Matching ratio is based on the optimal matching value which will vary with the category and additive amount of paint additives added.

●自由泡沫密度会依季节(温度,湿度)的不同而变化。

Free foam density will vary with the seasons (temperature, humidity).

●脱模时间会随成型品厚度的增加而延长。

Stripping time will be extended with the increase of the thickness of moldings.

●耐折条件:屈挠角度为 90度,频率为80次/min*4万次。

Folding endurance conditions: bending angle is 90 degrees and the frequency is 80 times / min * 40 thousand times

● 以上数据仅作参考,具体数据以实际操作为准。如需其他物性指标,请与我公司联系。

Data listed above is just for reference. The specific data is subjected to the practical operation. If other physical properties are required, please contact us.

未找到相应参数组,请于后台属性模板中添加
上一个

地址:

浙江省温岭市工业园区一号路科技园

       

Copyright © 浙江恒泰源聚氨酯有限公司 版权所有  浙ICP备20019453号 

中文 |EN | PT | ES | RU

搜索
搜索